diff --git a/board/amcc/canyonlands/bootstrap.c b/board/amcc/canyonlands/bootstrap.c
index 1d125b6..6b74743 100644
--- a/board/amcc/canyonlands/bootstrap.c
+++ b/board/amcc/canyonlands/bootstrap.c
@@ -168,7 +168,7 @@
 
 	if (i2c_write(I2C_EEPROM_ADDR, 0, 1, buf, 16) != 0)
 		printf("Error writing to EEPROM at address 0x%x\n", I2C_EEPROM_ADDR);
-	udelay(CFG_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
+	udelay(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
 
 	printf("Done\n");
 	printf("Please power-cycle the board for the changes to take effect\n");
diff --git a/board/amcc/canyonlands/canyonlands.c b/board/amcc/canyonlands/canyonlands.c
index 47667ee..e9186f8 100644
--- a/board/amcc/canyonlands/canyonlands.c
+++ b/board/amcc/canyonlands/canyonlands.c
@@ -29,11 +29,11 @@
 #include <asm/4xx_pcie.h>
 #include <asm/gpio.h>
 
-extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */
+extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#define CFG_BCSR3_PCIE		0x10
+#define CONFIG_SYS_BCSR3_PCIE		0x10
 
 #define BOARD_CANYONLANDS_PCIE	1
 #define BOARD_CANYONLANDS_SATA	2
@@ -86,7 +86,7 @@
 		SDR0_CUST0_NDFC_BW_8_BIT	|
 		SDR0_CUST0_NDFC_ARE_MASK	|
 		SDR0_CUST0_NDFC_BAC_ENCODE(3)	|
-		(0x80000000 >> (28 + CFG_NAND_CS));
+		(0x80000000 >> (28 + CONFIG_SYS_NAND_CS));
 	mtsdr(SDR0_CUST0, sdr0_cust0);
 
 	/*
@@ -99,13 +99,13 @@
 	mtsdr(SDR0_PCI0, 0xe0000000);
 
 	/* Enable ethernet and take out of reset */
-	out_8((void *)CFG_BCSR_BASE + 6, 0);
+	out_8((void *)CONFIG_SYS_BCSR_BASE + 6, 0);
 
 	/* Remove NOR-FLASH, NAND-FLASH & EEPROM hardware write protection */
-	out_8((void *)CFG_BCSR_BASE + 5, 0);
+	out_8((void *)CONFIG_SYS_BCSR_BASE + 5, 0);
 
 	/* Enable USB host & USB-OTG */
-	out_8((void *)CFG_BCSR_BASE + 7, 0);
+	out_8((void *)CONFIG_SYS_BCSR_BASE + 7, 0);
 
 	mtsdr(SDR0_SRST1, 0);	/* Pull AHB out of reset default=1 */
 
@@ -158,7 +158,7 @@
 		gd->board_type = BOARD_GLACIER;
 	} else {
 		printf("Board: Canyonlands - AMCC PPC460EX Evaluation Board");
-		if (in_8((void *)(CFG_BCSR_BASE + 3)) & CFG_BCSR3_PCIE)
+		if (in_8((void *)(CONFIG_SYS_BCSR_BASE + 3)) & CONFIG_SYS_BCSR3_PCIE)
 			gd->board_type = BOARD_CANYONLANDS_PCIE;
 		else
 			gd->board_type = BOARD_CANYONLANDS_SATA;
@@ -175,7 +175,7 @@
 		break;
 	}
 
-	printf(", Rev. %X", in_8((void *)(CFG_BCSR_BASE + 0)));
+	printf(", Rev. %X", in_8((void *)(CONFIG_SYS_BCSR_BASE + 0)));
 
 	if (s != NULL) {
 		puts(", serial# ");
@@ -208,7 +208,7 @@
  */
 phys_size_t initdram(int board_type)
 {
-	return CFG_MBYTES_SDRAM << 20;
+	return CONFIG_SYS_MBYTES_SDRAM << 20;
 }
 #endif
 
@@ -219,7 +219,7 @@
  *	inbound map (PIM). But the bootstrap config choices are limited and
  *	may not be sufficient for a given board.
  */
-#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
+#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
 void pci_target_init(struct pci_controller * hose )
 {
 	/*
@@ -234,7 +234,7 @@
 	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
 	 * strapping options to not support sizes such as 128/256 MB.
 	 */
-	out_le32((void *)PCIX0_PIM0LAL, CFG_SDRAM_BASE);
+	out_le32((void *)PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
 	out_le32((void *)PCIX0_PIM0LAH, 0);
 	out_le32((void *)PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1);
 	out_le32((void *)PCIX0_BAR0, 0);
@@ -242,12 +242,12 @@
 	/*
 	 * Program the board's subsystem id/vendor id
 	 */
-	out_le16((void *)PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID);
-	out_le16((void *)PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID);
+	out_le16((void *)PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
+	out_le16((void *)PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
 
 	out_le16((void *)PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY);
 }
-#endif	/* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+#endif	/* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
 
 #if defined(CONFIG_PCI)
 /*
@@ -314,9 +314,9 @@
 
 		/* setup mem resource */
 		pci_set_region(hose->regions + 0,
-			       CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
-			       CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
-			       CFG_PCIE_MEMSIZE,
+			       CONFIG_SYS_PCIE_MEMBASE + i * CONFIG_SYS_PCIE_MEMSIZE,
+			       CONFIG_SYS_PCIE_MEMBASE + i * CONFIG_SYS_PCIE_MEMSIZE,
+			       CONFIG_SYS_PCIE_MEMSIZE,
 			       PCI_REGION_MEM);
 		hose->region_count = 1;
 		pci_register_hose(hose);
@@ -362,16 +362,16 @@
 
 	/* Remap the NOR FLASH to 0xcc00.0000 ... 0xcfff.ffff */
 #if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
-	mtebc(pb3cr, CFG_FLASH_BASE_PHYS_L | 0xda000);
+	mtebc(pb3cr, CONFIG_SYS_FLASH_BASE_PHYS_L | 0xda000);
 #else
-	mtebc(pb0cr, CFG_FLASH_BASE_PHYS_L | 0xda000);
+	mtebc(pb0cr, CONFIG_SYS_FLASH_BASE_PHYS_L | 0xda000);
 #endif
 
 	/* Remove TLB entry of boot EBC mapping */
-	remove_tlb(CFG_BOOT_BASE_ADDR, 16 << 20);
+	remove_tlb(CONFIG_SYS_BOOT_BASE_ADDR, 16 << 20);
 
 	/* Add TLB entry for 0xfc00.0000 -> 0x4.cc00.0000 */
-	program_tlb(CFG_FLASH_BASE_PHYS, CFG_FLASH_BASE, CFG_FLASH_SIZE,
+	program_tlb(CONFIG_SYS_FLASH_BASE_PHYS, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_SIZE,
 		    TLB_WORD2_I_ENABLE);
 
 	/*
@@ -427,9 +427,9 @@
 	 * Disable square wave output: Batterie will be drained
 	 * quickly, when this output is not disabled
 	 */
-	val = i2c_reg_read(CFG_I2C_RTC_ADDR, 0xa);
+	val = i2c_reg_read(CONFIG_SYS_I2C_RTC_ADDR, 0xa);
 	val &= ~0x40;
-	i2c_reg_write(CFG_I2C_RTC_ADDR, 0xa, val);
+	i2c_reg_write(CONFIG_SYS_I2C_RTC_ADDR, 0xa, val);
 
 	return 0;
 }
@@ -445,7 +445,7 @@
 	/* Fixup NOR mapping */
 	val[0] = 0;				/* chip select number */
 	val[1] = 0;				/* always 0 */
-	val[2] = CFG_FLASH_BASE_PHYS_L;		/* we fixed up this address */
+	val[2] = CONFIG_SYS_FLASH_BASE_PHYS_L;		/* we fixed up this address */
 	val[3] = gd->bd->bi_flashsize;
 	rc = fdt_find_and_setprop(blob, "/plb/opb/ebc", "ranges",
 				  val, sizeof(val), 1);
diff --git a/board/amcc/canyonlands/config.mk b/board/amcc/canyonlands/config.mk
index 2330cae..551a817 100644
--- a/board/amcc/canyonlands/config.mk
+++ b/board/amcc/canyonlands/config.mk
@@ -37,5 +37,5 @@
 endif
 
 ifeq ($(dbcr),1)
-PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000
+PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000
 endif
diff --git a/board/amcc/canyonlands/init.S b/board/amcc/canyonlands/init.S
index 258fb5d..179dd32 100644
--- a/board/amcc/canyonlands/init.S
+++ b/board/amcc/canyonlands/init.S
@@ -47,10 +47,10 @@
 	 * enable SA_I
 	 */
 #ifndef CONFIG_NAND_SPL
-	tlbentry(CFG_BOOT_BASE_ADDR, SZ_16M, CFG_BOOT_BASE_ADDR, 4, AC_R|AC_W|AC_X|SA_G) /* TLB 0 */
+	tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_16M, CONFIG_SYS_BOOT_BASE_ADDR, 4, AC_R|AC_W|AC_X|SA_G) /* TLB 0 */
 #else
-	tlbentry(CFG_NAND_BOOT_SPL_SRC, SZ_4K, CFG_NAND_BOOT_SPL_SRC, 4, AC_R|AC_W|AC_X|SA_G)
-	tlbentry(CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+	tlbentry(CONFIG_SYS_NAND_BOOT_SPL_SRC, SZ_4K, CONFIG_SYS_NAND_BOOT_SPL_SRC, 4, AC_R|AC_W|AC_X|SA_G)
+	tlbentry(CONFIG_SYS_SDRAM_BASE, SZ_256M, CONFIG_SYS_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
 	tlbentry(256 << 20, SZ_256M, 256 << 20, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
 #endif
 
@@ -60,37 +60,37 @@
 	 * routine.
 	 */
 
-#ifdef CFG_INIT_RAM_DCACHE
+#ifdef CONFIG_SYS_INIT_RAM_DCACHE
 	/* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
-	tlbentry(CFG_INIT_RAM_ADDR, SZ_4K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G)
+	tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_4K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G)
 #endif
 
-	tlbentry(CFG_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_R|AC_W|SA_G|SA_I)
-	tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x20000000, 0xC, AC_R|AC_W|SA_G|SA_I)
-	tlbentry(CFG_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CONFIG_SYS_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, 0x20000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CONFIG_SYS_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_R|AC_W|SA_G|SA_I)
 
-	tlbentry(CFG_PCIE0_CFGBASE, SZ_16M, 0x00000000, 0xD, AC_R|AC_W|SA_G|SA_I)
-	tlbentry(CFG_PCIE1_CFGBASE, SZ_16M, 0x20000000, 0xD, AC_R|AC_W|SA_G|SA_I)
-	tlbentry(CFG_PCIE0_XCFGBASE, SZ_1K, 0x10000000, 0xD, AC_R|AC_W|SA_G|SA_I)
-	tlbentry(CFG_PCIE1_XCFGBASE, SZ_1K, 0x30000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CONFIG_SYS_PCIE0_CFGBASE, SZ_16M, 0x00000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CONFIG_SYS_PCIE1_CFGBASE, SZ_16M, 0x20000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CONFIG_SYS_PCIE0_XCFGBASE, SZ_1K, 0x10000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CONFIG_SYS_PCIE1_XCFGBASE, SZ_1K, 0x30000000, 0xD, AC_R|AC_W|SA_G|SA_I)
 
 	/* PCIe UTL register */
-	tlbentry(CFG_PCIE_BASE, SZ_16K, 0x08010000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CONFIG_SYS_PCIE_BASE, SZ_16K, 0x08010000, 0xC, AC_R|AC_W|SA_G|SA_I)
 
 	/* TLB-entry for NAND */
-	tlbentry(CFG_NAND_ADDR, SZ_16M, CFG_NAND_ADDR, 4, AC_R|AC_W|AC_X|SA_G|SA_I)
+	tlbentry(CONFIG_SYS_NAND_ADDR, SZ_16M, CONFIG_SYS_NAND_ADDR, 4, AC_R|AC_W|AC_X|SA_G|SA_I)
 
 	/* TLB-entry for CPLD */
-	tlbentry(CFG_BCSR_BASE, SZ_1K, CFG_BCSR_BASE, 4, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CONFIG_SYS_BCSR_BASE, SZ_1K, CONFIG_SYS_BCSR_BASE, 4, AC_R|AC_W|SA_G|SA_I)
 
 	/* TLB-entry for OCM */
-	tlbentry(CFG_OCM_BASE, SZ_16K, 0x00040000, 4, AC_R|AC_W|AC_X|SA_I)
+	tlbentry(CONFIG_SYS_OCM_BASE, SZ_16K, 0x00040000, 4, AC_R|AC_W|AC_X|SA_I)
 
 	/* TLB-entry for Local Configuration registers => peripherals */
-	tlbentry(CFG_LOCAL_CONF_REGS, SZ_16M, CFG_LOCAL_CONF_REGS, 4, AC_R|AC_W|AC_X|SA_G|SA_I)
+	tlbentry(CONFIG_SYS_LOCAL_CONF_REGS, SZ_16M, CONFIG_SYS_LOCAL_CONF_REGS, 4, AC_R|AC_W|AC_X|SA_G|SA_I)
 
 	/* AHB: Internal USB Peripherals (USB, SATA) */
-	tlbentry(CFG_AHB_BASE, SZ_1M, 0xbff00000, 4, AC_R|AC_W|AC_X|SA_G|SA_I)
+	tlbentry(CONFIG_SYS_AHB_BASE, SZ_1M, 0xbff00000, 4, AC_R|AC_W|AC_X|SA_G|SA_I)
 
 	tlbtab_end
 
@@ -99,8 +99,8 @@
 	 * For NAND booting the first TLB has to be reconfigured to full size
 	 * and with caching disabled after running from RAM!
 	 */
-#define TLB00	TLB0(CFG_BOOT_BASE_ADDR, SZ_256M)
-#define TLB01	TLB1(CFG_BOOT_BASE_ADDR, 1)
+#define TLB00	TLB0(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M)
+#define TLB01	TLB1(CONFIG_SYS_BOOT_BASE_ADDR, 1)
 #define TLB02	TLB2(AC_R|AC_W|AC_X|SA_G|SA_I)
 
 	.globl	reconfig_tlb0